HeadUnitAdvisor is reader supported. When you buy through links on our site we may earn an affiliate commission. Learn More.

How to remove JVC Car Stereo [3 Easy Methods]

How to remove JVC Car Stereo
How to remove JVC Car Stereo

Do you have a JVC car stereo that you want to remove? Whether you’re upgrading your car’s audio system or simply removing the old stereo, this guide will show you how to do it. We’ll walk you through the process step-by-step, so you can remove your JVC car stereo without any trouble.

We will also provide tips for how to avoid damaging your vehicle or the stereo during removal. So whether you’re a DIY enthusiast or just looking to save some money, read on for tips on how to remove a JVC car stereo yourself!

Things Required to remove JVC Car Stereo

  • Phillips Screwdriver
  • Flathead Screwdriver
  • Panel Popper Tool or Putty Knife (optional)

Method 1: How to remove JVC Car Stereo

How to remove JVC Car Stereo

1. Before attempting to remove your JVC car stereo, ensure that you have all the necessary tools on hand. You will need a small flathead screwdriver, a Phillips head screwdriver, and a panel removal tool.

2. Start by disconnecting the negative battery terminal. This will help to prevent any electrical shorts from occurring while you are working on the stereo.

3. Use the small flathead screwdriver to remove the two screws that secure the trim around the stereo. Gently pry the trim away from the dash, being careful not to damage it.

4. With the trim removed, you should now have access to the four screws that hold the stereo in place. Remove these screws and carefully pull the stereo out of the dash.

5. You will now need to disconnect the wiring harness from the back of the stereo. To do this, simply press down on the release tab and pull the connector off.

6. With the wiring disconnected, you can now remove the stereo from your vehicle.

Method 2: How to remove JVC Touchscreen car stereo

How to remove JVC Touchscreen car stereo

1. Unscrew and remove the four bolts that hold the stereo in place using a screwdriver.

2. Carefully pull the stereo out of the dash, being careful not to damage any of the surrounding wires or components.

3. Disconnect the wiring harness from the back of the stereo by unplugging it from the connectors.

4. Remove the trim ring around the stereo, if applicable.

5. Insert a flathead screwdriver or other tool into the release tabs on either side of the stereo and gently pry it out of the dash.

6. Reverse the process to install the new stereo, being sure to connect all of the wiring correctly. Test the new stereo before reinstalling all of the trim pieces.

Method 3: How To Remove JVC Car Stereo without Keys?

If you have lost your keys and are unable to remove your JVC car stereo, there are a few methods you can try.

1. Use a flathead screwdriver or other thin tool to pry the faceplate off of the stereo. Be careful not to damage the faceplate as you do this.

2. Once the faceplate is off, you should be able to see the screws holding the stereo in place. Remove these screws and carefully pull the stereo out of the dash.

3. If you still cannot remove the stereo, you may need to remove the entire dash panel in order to access the back of the stereo. This is a more difficult process and should only be attempted if you are confident in your ability to do so.

Once you have removed the stereo, you will need to use a wire hanger or other thin tool to reach behind and disconnect the wiring harness. With the wiring disconnected, you should be able to remove the stereo completely from your car.

FAQ’s

How do you take out a car stereo without the key?

There are a few ways to do this, but the most common is to use a flathead screwdriver. Insert the screwdriver into the slot on the side of the stereo and twist it until the stereo pops out. You may need to use a little force, so be careful not to damage the car’s interior. If you can’t get the stereo out with a screwdriver, you can try using a pair of pliers or a putty knife. Be careful not to scratch the dash or upholstery while you’re working.

How do you take out a JVC radio?

To take out a JVC radio, you will need to use a special removal tool that can be purchased at most electronics stores. Once you have the tool, simply insert it into the small opening on the side of the radio and twist in a counterclockwise direction. The radio should then come right out. If you are having trouble, consult your car’s owners manual for specific instructions.

How to remove a double DIN stereo without keys?

If you need to remove your double DIN stereo without the keys, there are a few methods you can use. One is to use a flat head screwdriver or a putty knife to pry the trim bezel off, which will then expose the screws holding the stereo in place. Another method is to remove the glove box and reach behind the stereo to access and remove the mounting screws. Once the screws are removed, you should be able to pull the stereo out of the dash. If you are still having trouble, you can consult your car’s owner’s manual for specific instructions on removing the stereo.

How to remove jvc car stereo with keys?

To remove a JVC car stereo with keys, first locate the two release buttons on the front of the unit. Next, insert the keys into the two slots and turn them counterclockwise to release the buttons. Finally, pull the unit out from the dash and disconnect the wiring.

How do I reset my JVC car stereo?

To reset your JVC car stereo, first disconnect the battery. Next, locate the reset button on the stereo. It is usually located in the front, near the display. Press and hold the reset button for about 5 seconds. The stereo should now be reset and ready to use.

How do I get my JVC KW r910bt out of demo mode?

There are a few ways that you can get your JVC KW r910bt out of demo mode. One way is to press and hold the “demo” button for about 5 seconds. This should reset the unit and take it out of demo mode. Another way is to disconnect the power source from the unit for about 30 seconds, then reconnect it. This should also reset the unit and take it out of demo mode. If neither of these methods work, you may need to consult your owner’s manual or contact JVC customer service for further assistance.

Related Posts

How To Connect Bluetooth to JVC Car Stereo

How To Reset JVC Car Stereo 

I am Miles Walker, founder of HeadunitAdvisor.com. I'm a car audio enthusiast and have been since I was a kid. I created the website to help people make the best decision when it comes to choosing and installing the new car stereo head unit. I have a degree in electrical engineering from UC Berkeley, and I love working on cars and audio equipment.

Leave a Comment

Headunitadvisor.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com

Copy link
Powered by Social Snap